Click the map to place the JTAC. Every range touched by the circle is reserved (and locked) for this JTAC.
Move the mouse over an area on the map to highlight it, click to reserve it, click again to release it. Several flights may book the same area (grey). The first flight that books an area can lock it (tick Lock in the list): the area is then red and nobody else can book it. The Las Vegas airspace cannot be selected. Airfields and procedures are chosen on the Planning page, where the route is planned too.
Reads the DCS server file (map, date, QNH, OAT, winds, clouds). The fields below are filled in; you can still change them.
QNH as set in the mission editor. For the takeoff and landing calculations and the QNH on the MDC and the strips every field gets the value corrected for the DCS altimeter error: QNH + elevation/1000 ft × (0.030 + 0.00117 × (T − 15)).
| Altitude (ft) | from (°) | Speed |
|---|
Wind direction accepts 0 to 360 only. The 1640 ft wind is not entered: DCS sets it to twice the ground wind speed.
Weather is the same as at the departure field.
Weights from the sheet Ordnance. The tool adds empty weight, stores and fuel (no crew or ammunition). Fuel burn depends only on flight time (AH-64D 1,200 lb/h, UH-1H 500 lb/h); there are no takeoff or landing tables for helicopters yet.
x
The A-10C has no DTC. Its mission-editor route presets (Lua, "presets = { … }") can be imported here; the export writes the current route as a preset into the imported file (or a new file) so it can be copied back into the DCS folder.
CombatFlite-Import reads the Lua file of one flight from CombatFlite: the turning points (position, altitude, speed), the departure and arrival airfield, the aircraft type and the callsign. The map is detected from the positions; if that fails, choose the map in the list and import again.
GeoJSON or KML with lines and polygons (country borders, training areas). Each file becomes one layer with its own colour.
The DTC import takes, for the F/A-18C, the waypoints of routes R1, R2 and R3 (sorted by waypoint number), their speeds and altitudes, and the time of the first waypoint, and lists the radio presets. For the AH-64D BLK.II it takes the route of Mission 1 (first enabled route with waypoints) and the radios of Preset 1.
The route starts at the departure airfield and ends at the arrival airfield. Waypoints in between can be moved with the arrows. The time of the first waypoint is entered in its ETA cell.
Import Geo-Daten: a list with one point per line: name, latitude, longitude (decimal degrees, comma or semicolon separated). Points are kept per map.
| # | Point | Leg (NM) | Heading (M) | WCA | Alt (ft) | Speed (kt) | Mach | ETA | Navaid | Position |
|---|
Marked with ◎ in the list above. Targets are not part of the distance, time or fuel; the DTC export writes them as R3. Departure and arrival points go to R1, the other waypoints to R2.
| # | Name | Position | Elevation (ft) |
|---|
Altitude and speed can be edited. An empty field takes the value of the previous waypoint (grey). The position can be overwritten: type coordinates (DD, DDM, DMS, MGRS) or the name of an intersection, navaid or airfield, for example XIBEL; + inserts a waypoint after the row. Mach uses true airspeed and the ISA temperature at the altitude. The ETA of each leg uses the speed of the waypoint it flies to.
Fuel burn follows the flight time only: 500 lb/h for the UH-1H and 1,200 lb/h for the AH-64D. Temperature and altitude are ignored.
| Alt (1000 ft) | KCAS | Mach |
|---|
| Mach | Drag index |
|---|
Climb, cruise and descent use the DCS flight-test data.
Status: Planning_Tool_4.xlsx of 24 Oct 2026. Points you have closed are no longer listed.
| Channel | COMM 1 | COMM 2 |
|---|
Linking with other flights (deconfliction, shared tanker and frequencies, evaluation) follows later.
The first bomb falls at the start and the last bomb at the end of the impact zone, so N bombs make N − 1 equal gaps: interval = (length / (N − 1)) / speed. The gap is measured on the ground; the speed of the bombs when they leave the aircraft is the speed of the aircraft. Use this value as the ripple time (ms) in the weapon settings of the aircraft.
NOTAMs for the flight day and the map above, in ICAO format. They are shown on the route map and checked against the route (hint only).
The route check looks at the position and the altitude of the legs (not at the times). Once the server version has user accounts, only the administrator will enter NOTAMs; until then this tool is open to everyone.